Survey WorkbookA field manual for survey instructionGet COGO
Field observations

Height of instrument exercise: pick out the intermediate sights

Reduce three detail elevations from one setup, carry a turning point forward and test why intermediate sights stay out of the closure sum.

On this pageWork the bookRead several elevations from the first line of sightCheck the run without adding the detail shotsMarking and interpretation

Six rod readings do not automatically belong in a single sum. A backsight establishes an instrument height. An intermediate sight gives a detail elevation from that height. A foresight to a turning point transfers the run. Treating every detail shot as a foresight can make a well-observed setup appear to lose metres of elevation.

Work the book

All readings are in metres. Start at BM-X, accepted elevation 105.250 m. The crew occupies two instrument setups. From the first, it observes three detail points D1, D2 and D3, then turns on TP-A. From the second it closes on BM-Y, accepted elevation 105.115 m. Compute both heights of instrument, all detail elevations, the turning-point elevation and the observed closing difference.

Setup Point BS IS FS
1 BM-X 1.284
1 D1 1.205
1 D2 1.632
1 D3 0.998
1 TP-A 1.409
2 TP-A 0.934
2 BM-Y 0.939

Before doing the arithmetic, draw a horizontal line on a profile sketch to represent the first instrument sight line. Assuming upright staffs, circle the detail point that must be highest. Then find the two entries that touch the same turning point and mark the setup change between them.

Read several elevations from the first line of sight

The first height of instrument is 105.250 + 1.284 = 106.534 m. Subtract each intermediate sight separately from that same height. D1 is 105.329 m, D2 is 104.902 m and D3 is 105.536 m. D3 is highest because its 0.998 m reading is shortest. D2, with the longest detail reading, is lowest. This ranking is an independent check on the direction of your subtractions.

The foresight on TP-A gives 106.534 − 1.409 = 105.125 m. The second setup then takes 0.934 m as its backsight on TP-A. Adding it to the turning-point elevation gives the new HI of 106.059 m. Subtract the closing foresight of 0.939 m for a computed BM-Y elevation of 105.120 m. The observed close is +0.005 m high relative to the supplied 105.115 m.

Check the run without adding the detail shots

The transfer backsights total 1.284 + 0.934 = 2.218 m. The transfer foresights total 1.409 + 0.939 = 2.348 m. Their difference is −0.130 m. Starting elevation plus that change gives 105.120 m, the same computed ending elevation. The known benchmark difference is 105.115 − 105.250 = −0.135 m; the two changes differ by +0.005 m.

D1, D2 and D3 drop out because none carries the line of levels into the next setup. Their elevations still matter to the finished job. An error in D2 can spoil a design profile even though it cannot spoil this run’s BS-minus-FS agreement. If D2 was actually read as 1.362 m rather than the booked 1.632 m, its revised elevation would be 105.172 m, 0.270 m higher. The closing difference at BM-Y would remain +0.005 m.

Marking and interpretation

Award marks for the two setup heights, correct detail ranking, distinct readings on the turning point and the signed comparison with BM-Y. Ask students to label the 0.005 m as a discrepancy rather than declaring acceptance without an applicable standard. A closure test can support a decision only in the context of the required accuracy, observation method and checks.

For an extension, have another student create a detailed ground profile from D1, D2 and D3. Ask what additional observations are missing. Three reduced elevations provide vertical information, but the profile also needs the positions or horizontal distances along the intended line. That distinction is easy to miss when a neat level-book column looks complete.

References

Practice the same traverse in COGO