Compute earthwork volume between unequal station intervals
Use three cut areas and their chainages, then insert a measured middle section to see how average-end-area volume responds to extra field data.
On this page
Exercise sheetWork the original intervalsInsert the measured cross sectionExplain the difference in the area diagramWhat to award in a worked answerAn earthwork table lists areas of 14, 22 and 10 square metres. Their mean is easy to compute, but it will not give the right average-end-area quantity over this route. The cross sections are at chainages 0, 25 and 60 m. The lengths between stations differ, so each interval needs its own pair of end areas and its own length.
Exercise sheet
| Station chainage (m) | Measured cut area (m²) |
|---|---|
| 0 | 14.0 |
| 25 | 22.0 |
| 60 | 10.0 |
Assume all three cross sections are perpendicular to the alignment and their cut areas were measured consistently to the same design surface. There is no fill in the exercise. Report the geometric cut volume in cubic metres using average end area. Then recalculate after the surveyor supplies an additional measured cut area of 19.0 m² at chainage 40. Explain why the answer changes.
Work the original intervals
Between chainages 0 and 25, the interval length is 25 m and the mean end area is (14 + 22)/2 = 18 m². Multiplication gives 450 m³. From chainage 25 to 60 the interval length is 35 m, with mean area (22 + 10)/2 = 16 m². This contributes 560 m³. The original total is 1,010 m³.
Check the dimensions before rounding. An area in square metres multiplied by metres gives cubic metres. The first interval’s mean area lies between its two end areas, so its volume must lie between 14 × 25 and 22 × 25 under the chosen interpolation. The computed 450 lies between 350 and 550. Repeat the bound for the second interval: 350 to 770 m³ contains 560.
Insert the measured cross section
The 0–25 interval has exactly the same inputs as before. Retain its 450 m³. The old 25–60 interval must now be replaced by two intervals, 25–40 and 40–60. On the first, length 15 × (22 + 19)/2 gives 307.5 m³. On the second, length 20 × (19 + 10)/2 gives 290.0 m³.
The revised total is 450 + 307.5 + 290.0 = 1,047.5 m³. The difference is +37.5 m³. Adding the two new volumes to the original 1,010 would double-count the old 35 m interval. Draw a horizontal line with tick marks at the four chainages and cross out the superseded interval before adding volumes.
Explain the difference in the area diagram
Plot chainage horizontally and area vertically. The original straight line between 22 at station 25 and 10 at station 60 predicts an area of about 16.857 m² at station 40. The additional measured area is 19, about 2.143 m² above that old line. Connecting the new point to the two old ends introduces a triangular increase in the area-under-the-area-plot. Half of 35 m times about 2.143 m² equals approximately 37.5 m³, the independent check on the arithmetic.
This diagram shows the assumption behind the method. End areas can enclose a reach where width, depth or slope changes sharply between measured sections. Another observation can move the computed quantity in either direction. The exercise does not establish a universal station spacing or an exact volume for arbitrary terrain.
What to award in a worked answer
Give credit for using interval lengths, keeping the intermediate volumes, replacing the correct interval and interpreting the added observation. A final answer with no units or station limits is difficult to audit. For an extension, ask the student to name an appropriate place for another cross section, such as a sudden grade break or widening visible in field notes. Require an explanation of what change the new section would capture. The objective is a defensible measurement plan as well as a correct number.