Survey WorkbookA field manual for survey instructionGet COGO
Mapping and measurement

Measure a map after the printer changes its scale

Use a printed scale bar to recover the effective map scale, calculate a route length and quantify the error from trusting the original ratio.

On this pageMeasurement sheetRecover the effective scaleCalculate the route in bar lengthsWork out the cost of using the old labelInstructor check and extension

A plan is labeled 1:2,500. On the original sheet a 100 m scale bar would measure 40 mm. On the copy on your desk the same bar measures 36 mm. Before you put a ruler on the access road, decide which piece of information traveled with the drawing when the paper size changed.

Measurement sheet

Item measured on the printed copy Ruler reading
Scale bar labeled 0 to 100 m 36.0 mm
Road segment from gate to bend 54.0 mm
Road segment from bend to shed 27.0 mm
Clear width between two mapped boundaries 4.5 mm

Assume the sheet was reduced uniformly in both directions. The road consists of the two straight segments listed. Calculate the actual map ratio of this printed copy, the total ground length along the road and the mapped clear width. Work each in metres and keep the 100 m bar available for a check.

Recover the effective scale

The ruler’s 36 mm represents 100,000 mm on the ground. Dividing ground by paper gives a representative fraction denominator of 100000/36, about 2777.78. The printed copy therefore has an effective scale near 1:2,778. Its fraction is smaller than the original 1:2,500 because the same ground distance now takes less space on the sheet.

A second route to the answer is the print reduction factor. The bar should have been 40 mm and is now 36 mm, so the linear reduction is 36/40 = 0.90. Divide the original denominator by 0.90 to get the same effective denominator. Multiplying by 0.90 instead would predict a larger drawing, contradicting the measured bar.

Calculate the route in bar lengths

The first road segment spans 54/36 = 1.5 bar lengths, or 150 m. The second spans 27/36 = 0.75 bar lengths, or 75 m. Their combined route length is 225 m. It is important to add the two measured segments. A single ruler measurement from the gate straight to the shed would give the chord across the bend and answer a different question.

The mapped clear width is 4.5/36 × 100 = 12.5 m. Dividing all three paper measurements by the same bar length avoids converting millimetres to metres repeatedly. The units cancel in the paper-length ratio and the label on the bar supplies the ground unit.

Work out the cost of using the old label

Using 1:2,500 directly on the copy would turn the 81 mm road measurement into 202.5 m. The calculated route would be short by 22.5 m, or 10 percent of the correct 225 m. The obsolete ratio can still produce a plausible answer. A comparison against the printed bar exposes the error independently of any knowledge of the road.

Consider measurement precision too. If a single length can be read only within about 0.2 mm, that reading uncertainty corresponds to roughly 0.56 m at this copy scale. The 12.5 m mapped width should therefore carry a sensible reporting precision. A map with thick boundary symbols may introduce more uncertainty than the ruler. Measuring the graphic cannot establish a construction clearance or a surveyed boundary position.

Instructor check and extension

Award the ratio mark for a dimensionless ground-to-paper comparison with matching units. Award the length marks for the two-segment route and the separately calculated width. A response of 202.5 m merits recognition for arithmetic with the printed denominator, followed by a request to identify which scale information survived resizing.

As an extension, suppose a second 100 m bar printed vertically measures 35 mm. A single scale factor would then fail to describe both axes. A sloping road segment would require direction-dependent correction or a new undistorted copy. Ask the class which checks they would add before measuring a screenshot or a photograph taken at an angle. That discussion connects a simple ratio exercise to the quality of the source image.

References

Practice the same traverse in COGO